Products by Teseq
Teseq AG, formerly Schaffner Test Systems is a supplier of Electromagnetic compatibility (EMC) test solutions. They develop and manufacture instruments for EMC emissions and immunity testing both for radiated and conducted emissions and immunity. Teseq operates ISO 17025 accredited calibration laboratories with EMC specialization.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| | TESEQ HLA 6120 Loop Antenna 9 kHz – 30 MHz | The HLA 6120 is ideal for the 3 m magnetic field measurements as required e.g. by CISPR 11 (reference CISPR 16-1-4 and CISPR 16-2-3) and FCC 18. The built-in preamplifier matches the extremely low impedance of the loop to the measuring receiver. The ... View Details >>
|
|
|
| | TESEQ ITS 6006 Radiated Immunity System 6 GHz | The ITS 6006 consist of an integrated RF signal generator, RF switch and EUT monitoring interfaces. The unit is designed for various radiated EMC applications in the 80 MHz to 6 GHz frequency range. In addition to the generator, the system includes t... View Details >>
|
|
|
| | TESEQ KEMA 801 RF Attenuation Clamp | The KEMA 801 is recommended as an additional decoupling network (ferrite tube clamp) for immunity test according to IEC/EN 61000-4-6 when using the clamp injection method. It shall be inserted on all the cables between EUT and AE except the cable und... View Details >>
|
|
|
| | TESEQ KEMZ 801 EM Clamp for IEC/EN 61000-4-6 | EC 61000-4-6 (EN 61000-4-6) defines three basic types of transducer used for the injection of test signals into the equipment under test (EUT). The basic requirement is to inject a known level of RF signal onto the cable of the EUT at each test frequ... View Details >>
|
|
|
|
|
| | TESEQ MD 103 ESD Pulse Calibration Set | Calibration procedures on ESD generators call for high class test equipment and a carefully configured test rig. All the elements incorporated within the measurement chain must be matched to one another before highly accurate measurements with minima... View Details >>
|
|
|
| | TESEQ MD 200 High Voltage Differential Probe | The Teseq MD 200 and MD 200A high voltage differential probes are ideally suited to allow EMC engineers to verify their conducted EMC test generators periodically. Their performance permits to be used for many other purposes where higher voltages hav... View Details >>
|
|
|
| | TESEQ MD 200A High Voltage Differential Probe | The Teseq MD 200 and MD 200A high voltage differential probes are ideally suited to allow EMC engineers to verify their conducted EMC test generators periodically. Their performance permits to be used for many other purposes where higher voltages hav... View Details >>
|
|
|
| | TESEQ MD 300 Surge Pulse Current Probe Set | The MD 300 probe has been specially designed to verify surge current pulses as specified in IEC/EN 61000-4-5, ANSI C62.41 and their derivates.
The main advantage of the MD 300 current probe is, that the measuring system is physically isolated from... View Details >>
|
|
|
|
|
| | TESEQ NFPS 1 Near Field Probe Set | A diagnostic “tool kit” for use in both electrical and mechanical environments featuring three hand held probes (two magnetic, one electric) covering the frequency range 9 kHz to 1 GHz together with a 30 dB pre-amplifier, power adaptor and check ... View Details >>
|
|
|
| | TESEQ NNB 51 Dual-line -V-LISN | Line impedance stabilization network (LISN) such as the NNB 51 is used to measure distortion signals on the mains cord of electrical equipment under test (EUT). The distortion signals are usually generated or picked up inside of the EUT and the mains... View Details >>
|
|
|
| | TESEQ NNB 52 Four-Line -V-LISN | Line impedance stabilization network (LISN) such as the NNB 52 is used to measure distortion signals on the mains cord of electrical equipment under test (EUT). The distortion signals are usually generated or picked up inside of the EUT and the mains... View Details >>
|
|
|
| | TESEQ NSG 434 ESD Simulator 8.8kV | Ergonomic design and advanced functionality. The pistol-shaped NSG 434 simulator is designed to sit comfortably in the operator’s hand, with current operating conditions constantly displayed and clearly visible.
NSG 434’s microprocessor-based ... View Details >>
|
|
|
| | TESEQ NSG 437 ESD Simulator 30kV | The NSG 437 simulator is designed to sit comfortably in the operator’s hand, with current operating conditions constantly displayed and clearly visible. The simulator is ergonomically designed to be held easily for long duration test procedures.
... View Details >>
|
|
|
| | TESEQ NSG 439 Robotic ESD Simulator 30kV | Complete system solution with 30 kV ESD simulator for robotic applications.
Today’s growing trend towards miniaturizing and more comprehensive product standards means that ESD testing is now required not only for operating controls, but also for... View Details >>
|
|
|
|
|
| | TESEQ NSG 3025 Burst Generator 4.8 kV | The compact NSG 3025 is fully capable of running standard tests to EN 61000-4-4, IEC 61000-4-4, etc. as well as handling tests to both product and company standards. It has been designed for certification, development laboratory and on-site purposes.... View Details >>
|
|
|
