Products by Teseq
Teseq AG, formerly Schaffner Test Systems is a supplier of Electromagnetic compatibility (EMC) test solutions. They develop and manufacture instruments for EMC emissions and immunity testing both for radiated and conducted emissions and immunity. Teseq operates ISO 17025 accredited calibration laboratories with EMC specialization.
| | TESEQ NSG 1025 Fast Transient/Burst Generator | Standards such as the IEC 801-4, DIN/VDE 0843-4 . CENELEC HD 481 .4, etc. call for interference voltage tests to be carried out on instruments and systems using pulse bursts similar to those that occur in practice when electrical equipment is switche... View Details >>
|
|
|
| | TESEQ AMZ 41 Absorbing Clamp | The absorbing clamp AMZ 41 has been designed for measurement of radio interferences emitted from electrical instruments via their connecting leads. The absorbing clamp measurement method (ACMM) is described in Clause 7 of CISPR 16-2-2. The absorbing ... View Details >>
|
|
|
|
|
|
|
| | TESEQ CBL 6111D BILOG Antenna 30 MHz – 1 GHz | The CBL 6111 is a high performance ultra wideband BiLog® antenna designed for emission and immunity EMC testing. This is the original ‘classic’ BiLog® combining two antennas in one, making savings of at least 20 - 30% on test time and red... View Details >>
|
|
|
| | TESEQ CBL 6112D BILOG Antenna 30 MHz – 2 GHz | The CBL 6112D operates over the unprecedented, wide range 30 MHz to 2 GHz. It effectively combines the performance of three standard EMC antennas, the Biconical, the Log Periodic and the Waveguide Horn. Considerable savings in the order of 40 - 50% c... View Details >>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| | TESEQ CDN HSS-2 Coupling Decoupling Network | The Coupling Decoupling Network CDN HSS-2 is designed for convenient surge testing with 1.2/50 μs pulses, as defined in IEC/EN 61000-4-5, on unshielded symmetrical high speed telecommunication lines e.g. Ethernet. Coupling modes to 1, 2 or 4... View Details >>
|
|
|
| | TESEQ CFL 9206 Transient Limiter | The CFL has been designed to interface between a transducer (antenna, line network) and measuring equipment (receiver, spectrum analyzer). The CFL 9206 assists in preventing damage to input circuits of measuring equipment from high level transients o... View Details >>
|
|
|
|
|
|
|
| | TESEQ CMAD 10 Common Mode Absorption Device | Reproducible emissions measurements require a defined line termination for the frequency range where connected lines provide a significant influence on the emissions. The key parameter is the asymmetrical impedance (common-mode impedance) which can b... View Details >>
|
|
|
| | TESEQ CMAD 20A Common Mode Absorption Device | Reproducible emissions measurements require a defined line termination for the frequency range where connected lines provide a significant influence on the emissions. The key parameter is the asymmetrical impedance (common-mode impedance) which can b... View Details >>
|
|
|
|
|
| | TESEQ CVP 2200A Capacitive Voltage Probe | The Capacitive Voltage Probe (CVP) is designed for measuring asymmetrical disturbances on cables with capacitive coupling principle. It gives the opportunity to do the measuring without disconnection of the tested cable (“in-situ”) and it avoids ... View Details >>
|
|
|
| | TESEQ DC LISN M2-25-V2 Dual-Line LISN for GCPC | Teseq introduces a new Line Impedance Stabilization Network (LISN) for conducted emissions testing of Grid Connected Power Conditioners (GCPC). The DC-LISN-M2-25-V2 is designed for measuring disturbances on DC power ports in the frequency range from ... View Details >>
|
|
|
| | TESEQ DC LISN M2-100 Dual-Line LISN for GCPC | Teseq introduces a new Line Impedance Stabilization Network (LISN) for conducted emissions testing of Grid Connected Power Conditioners (GCPC). The DC-LISN-M2-100 is designed for measuring disturbances on DC power ports in the frequency range from 15... View Details >>
|
|
|
|
|
|
|
