»  Categories   »      Solid State Amplifier   »    RF Amplifier   »    Mid-Power Amplifier   »    Low Frequency Amplifier   »    Broadband Amplifier   »    Amplifier  

image enlarge

Amplifier Research 350AH1 RF Amplifier 10 Hz – 1 MHz 350W

Description

Amplifier Research 350AH1 amplifier is a portable, self-contained, air-cooled, broadband, solid state amplifier unit designed for laboratory applications where instantaneous bandwidth, high gain and moderate power output are required. When used with an RF sweep generator, the 350AH1 will provide up to 350 watts of output power.

Housed in a stylish contemporary enclosure, the unit provides instantaneous power for typical applications such as magnetic susceptibility testing, 4-10 kHz requirement of CS114 of MIL-Std-461F, antenna and component testing, Watt-meter calibration and as a driver for higher power amplifiers.

The 350AH1 is powered by a high efficiency switching supply, with auto ranging AC input circuitry which will automatically accept voltages from 90 to 260 VAC in the 47 to 63 Hz frequency range. The RF amplifier stages are protected from overtemperature and over-current conditions by removing the DC voltage to them when a fault is detected.

The digital display on the front panel indicates the operational status and any pending fault conditions when an over-temperature, over-current or power supply fault has occurred. The unit can be returned to normal operation when the condition has been cleared. The unit also includes digital control for both local and remote control of the amplifier. The RISC microprocessor controller board provides IEEE-488 (GPIB), USB, Ethernet and asynchronous full duplex RS-232 communication control of all amplifier functions.

Two 350AH1 amplifiers may be used together in a "bridged" output configuration by supplying the same signal to both amplifiers and using the internal signal inversion feature of one amplifier. The amplifier output grounds are connected and the load is placed across the two amplifier outputs.

Features

  • Portable
  • Solid state
  • Broadband
  • High gain
  • Mismatch tolerant
  • Modulation capability
  • RF connector – Type BNC
  • Interface – IEEE-488, RS-232

Specifications

OPERATION

Class AB Linear

FREQUENCY RESPONSE

10Hz–1 MHz instantaneously

POWER OUTPUT (1.79 Ohm load)

CW, Minimum

350 watts, 10Hz–300kHz

350–55 watts, 300kHz–1MHz

Voltage Output, Minimum

25 Vrms, 10Hz–300kHz

25-10 Vrms, 300kHz–1MHz

Current Output, Minimum

14 Arms, 10Hz–300kHz

14–5.5 Arms, 300kHz–1MHz

FLATNESS

±1.0 dB, 10Hz–300kHz

±4.0 dB, 300kHz–1MHz

GAIN (POWER)

47 dB minimum, 10Hz–300kHz

39 dB minimum, 300kHz–1MHz

GAIN CONTROL RANGE

15 dB minimum

INPUT SIGNAL

0–2 Vrms

INPUT IMPEDANCE

600 ohms typical

OUTPUT IMPEDANCE

< 1Ω typical

MISMATCH TOLERANCE

100% of rated power without fail.

MODULATION CAPABILITY

Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal

PRIMARY POWER

90–260 VAC

47 to 63 Hz, single phase

1200 watts maximum

CONNECTORS

RF INPUT

Type BNC female

RF OUTPUT

5-way binding posts

REMOTE CONTROL

IEEE-488

24 pin female

RS-232

9 pin subminiature D (female)

USB

Type B (female)

Ethernet

RJ-45

REMOTE INTERLOCK

15 pin subminiature D

COOLING

Forced air (self contained fans)

SIZE (W x H x D)

50.3 x 19.9 x 37.6 cm, 19.8 x 7.85 x 14.8 in

WEIGHT

25 kg (55 lb)

Standards

CISPR
CISPR 11
CISPR 14 - 1
CISPR 14 - 2
CISPR 14 - 2
CISPR 16 - 1
CISPR 16 - 2
CISPR 16 - 3
CISPR 16 - 4
CISPR 22
CISPR 24
IEC
IEC/TR EN 61000 - 1 - 1
IEC/TR EN 61000 - 2 - 1
IEC/TR EN 61000 - 2 - 3
IEC EN 61000 - 3 - 2
IEC EN 61000 - 3 - 4
IEC/TC EN 61000 - 3 - 5
IEC EN 61000 - 4 - 2
IEC EN 61000 - 4 - 3
IEC EN 61000 - 4 - 4
IEC EN 61000 - 4 - 5
IEC EN 61000 - 4 - 6
IEC EN 61000 - 4 - 7
IEC EN 61000 - 4 - 8
IEC EN 61000 - 4 - 9
IEC EN 61000 - 4 - 11
European
EN 50 081 part 1
EN 50 081 part 2
EN 55 011
EN 55 013
EN 55 014
EN 55 015
EN 55 020
EN 55 022
EN 55 024
EN 50 082 part 1
EN 50 082 part 2
EN 50 093
American
FCC Part 15
MIL-STD - 461E